Model

DSO2D15

DSO2D10

DSO2D15

DSO2C10

Bandwidth

150MHz

100MHz

150MHz

100MHz

Oscilloscope Channels

2Ch

2Ch

2Ch

2Ch

Arbitrary Function Generator

1Ch

1Ch

Horizontal

SEC/DIV Range

2ns/div to 100s/div, in a 1, 2, 5 sequence

Delta Time Measurement Accuracy

(Full Bandwidth)

Single, sampling mode

±  (1 sample interval + 100ppm × reading + 0.6ns)

>16 times above average

±  (1 sample interval + 100ppm × reading + 0.4ns)

Sample interval = s/div ÷ 200

Vertical

A/D Converter

8-bit resolution, each channel sampled simultaneously

VOLTS/DIV Range

2mV/div to 10V/div at input BNC

Offset Range

2mV/div ~ 200mV/div, ±1V

500mV/div ~ 10V/div, ±50V

Selectable Analog Bandwidth Limit (Typical)

20MHz

Low Frequency Response ( − 3db)

≤10Hz at BNC

Rising Time  at  BNC (Typical)

DSO2C10

 DSO2C15

 DSO2D10

DSO2D15

≤3.5ns

≤2.4ns

≤3.5ns

≤2.4ns

DC Gain Accuracy

±3% for Normal or Average acquisition mode, 10V/div to 10mV/div

±4% for Normal or Average acquisition mode, 5mV/div to 2mV/div

Vertical Offset Accuracy

±0.1div±2mV±1% Offset

Mathematical Operation

+,  − , ×, /, FFT

FFT

Window Function Types: Rectangle, Hanning, Hamming, Blackman, Bartlett and Flat Top

Voltage Measurement Repeatability, Average Acquisition Mode

 Under the same setting and environment, ≥16 waveforms are sampled, ΔV of any two averages:

± (3% × value + 0.05 div)

Note: Bandwidth reduced to 6MHz when using a 1X probe  

Acquisition

Sample Rate Range

1GSa/s (single channel), 500MSa/s (dual channels)

Acquisition Modes

Normal, Peak, Average & High Resolution

Waveform Interpolation

(sin x)/x

Acquisition Rate (Typical)

Up to 2000 waveform per second per channel (Normal acquisition mode, no measurement)

Minimum Detection Pulse Width

2ns

Single Sequence

Acquisition Mode

Acquisition Stop Time

Normal, Peak Detect

Upon single acquisition on all channels simultaneously

Average

After N acquisitions on all channels simultaneously, N can be set to 4, 8, 16, 32, 64 or 128

Memory Depth

Maximum 8M for single channel (4K, 40K, 400K, 4M, 8M optional)

Maximum 4M for dual channels (4K, 40K, 400K, 4M optional)

Trigger

Trigger Type  

Edge, Pulse width, Video, Slope, Overtime, Window, Pattern, Interval, Delay, UART, LIN, CAN, SPI, lIC

Trigger Level Range

±5 divisions from the center of the screen

Mode

Auto, Normal, Single

Level

CH1 ~ CH2

±5 divisions from the center of screen

EXT

0~3.3V [CMOS]

Holdoff Range

20ns ~ 10s

Trigger Level Accuracy

CH1~CH2

0.2 div × volts/div within ±4 divisions from the center of the screen

EXT

± (Set value × 6% + 40mV)

Trigger Sensitivity

±0.2div

Edge Trigger

Slope

Rising, Falling, Rising & Faling

Source

CH1 ~ CH2, Line, External

Pulse Trigger 

Polarity 

Positive, Negative

Condition

< ， > ， != ，=

Source 

CH1 ~ CH2

Pulse Width Range

  8ns ~ 10s

Accuracy

8ns

Video Trigger 

Signal standard 

NTSC, PAL 

Signal source

CH1 ~ CH2

Synchronization 

ScanLine, LinrNum, OddField, EvenField and AllField

Slope Trigger 

 Slope 

 Nse, Fall

Condition

< ,   > ,   != ,   =

Source 

CH1 ~ CH2

Time Range 

8ns ~ 10s

Accuracy 

8ns

Overtime Trigger

Source 

CH1 ~ CH2,

Polarity 

Positive, Negative

Time range 

8ns ~ 10s

Accuracy

 8ns

Window Trigger 

Source

 CH1 ~ CH2

Pattern Trigger

Pattern

0: low level; 1: high level; X: ignore 

Level

 CH1 ~ CH2

Interval Trigger

Slope

Rising, Falling

Condition

<, >, !=, =

Signal Source 

 CH1 ~ CH2

Time Range 

8ns ~ 10s

Accuracy

 8ns

Under Amp Trigger

Polarity 

Positive, Negative

Condition 

<, >, !=, =

Source

 CH1 ~ CH2

Time Range 

8ns ~ 10s

Accuracy

 8ns

UART Trigger

Condition

Start, Stop, Data, Parity Error, COM Error

Source

CH1 ~ CH2

Data Format

Hex

Condition

<, >, !=, =

Data Length

1 byte

Data Bits Width

5 bit, 6 bit, 7 bit, 8 bit

Parity Check

None, Odd, Even

Idle Level

High, Low

Baud Rate (Selectable)

110/300/600/1200/2400/4800/9600/14400/19200/38400/57600/115200/230400/380400/460400 bit/s

Baud Rate (Custom)

300bit/s ~ 334000bit/s

LIN Trigger

Condition

Interval Field, Sync Field, Id field, Sync Id Error, Identifier, Id and Data

Source

CH1 ~ CH2

Data Format

Hex

Baud Rate (Selectable)

110/300/600/1200/2400/4800/9600/14400/19200/38400/57600/115200/230400/380400/460400 bit/s

Baud Rate (Custom)

300bit/s ~ 334000bit/s

CAN Trigger

Condition

Start Bit, Remote Frame, Data Frame Id, Frame Id, Data Frame Id A, Error Frame, All Error, Ack Error, Overload Frame

Source

CH1 ~ CH2

Data format

Hex

Baud Rate (Selectable)

10000, 20000, 33300, 500000, 62500, 83300, 100000, 125000, 250000, 500000, 800000,1000000

Baud Rate (Custom)

5kbit/s ~ 1Mbit/s

SPI Trigger

Source (SDA/SCL)

CH1 ~ CH2

Data Format

Hex

Data Length

4, 8, 16, 24, 32

IIC Trigger

Source (SDA/SCL)

CH1~CH2

Data Format

Hex

Data Index

0~3

Condition

Start Bit, Stop Bit, No Ack, Address, Restart, Address and Data

Input

Number of Channels

2 analog channels

Input Coupling

DC, AC or GND

Input Impedance, DC Coupled

20pF ± 3pF, 1MΩ ± 2%

Probe Attenuation

1X, 10X

Supported Probe Attenuation Factors

1X, 10X, 100X, 1000X

Overvoltage Category

300V CAT II

Maximum Input Voltage

300V RMS  (10X)

Isolation Between Channels

>40dB

Delay Deviation Between Channels

<500ps

Measurements

Cursors

Voltage difference between cursors: ΔV

Time difference between cursors: ΔT

Reciprocal of ΔT in Hertz (1/ΔT)

Automatic Measurements

PkPk, Frequency, Average, Max, Min, Period, Vtop, Vmid, Vbase, Vamp, RMS, R-Overshoot, PeriodRms, F-Preshoot, PeriodRms, PeriodAvg, RiseTime, FallTime, +Width,  − Width, +Duty,

− Duty, FRR, FFF, F − Overshoot, R − preshoot, BWidth, FRF, FFR, LRR, LRF, LFR and LFF

DVM

Data source

 CH1, CH2

Measurement type

DC RMS, AC RMS, DC

Frequency meter 

hardware 6 bits frequency meter 

Math Operation

Source

CH1~CH2

Operator

+,  − , x, /, FFT

FFT

Point

1024

Window

Rectangle, Hanning, Hamming, Blackman, Bartlett, Flattop

Display

Show only or show all

Vertical scale

dB, VRms

Storage

Save/Recall (Non-volatile)

9 types of files can be saved and recalled internally, including settings, waveforms, and references

Save to External Memory

CSV file, BMP picture (24 bit)

Arbitrary Waveform Generator

Channel  

1

Standard Waveforms

Sine, Square, Ramp, Exponential, Noise, DC

Sin 

Frequency range

0.1Hz ~ 25MHz

Square / Pulse

Frequency range

0.1Hz ~ 10MHz

Duty

1% ~ 99%

Triangular Wave 

Frequency range

0.1Hz ~ 1MHz

Ramp

Frequency range

0.1Hz ~ 1MHz

Symmetry

0% ~ 100%

Exponential

Frequency range

0.1Hz ~ 5MHz

Noise 

Bandwidth

>25MHz

DC offset 

Range

±3.5V, high impedance 

±1.75V, 50Ω

Resolution

100µV or 3 bits, take the greater one

Accuracy

2% (1kHz)

Arbitrary waveform

Frequency Range

1µHz ~ 25MHz

Wave length

4096

Support PC download and external memory recall

Output impedance 

50 Ω + 1%, high impedance

Amplitude 

Output range

10mV ~ 7Vp-p (high impedance )

5mV ~ 3.5Vp-p (50Ω)

Amplitude accuracy

±3dB

Waveform Depth 

4KSa

Frequency Resolution

1uHz

Frequency Accuracy 

<10KHz,100ppm

>10KHz,50ppm

Modulation

FM

Modulation waveform

Sine, square, ramp

Modulation frequency

1Hz ~ 50kHz

Modulation deviation

0.1Hz ~ Carrier frequency

AM

Modulation waveform

Sine, square, ramp

Modulation frequency

1Hz ~ 50KHz

Modulation depth

0% ~ 120%

Burst

Types of

N Cycle, Infinite

Number of cycles

1 ~ 1024

Trigger source

Manual

Trigger Input Signal Source

Level

MOS

Probe Compensator Output

Output Voltage (Typical)

5V

Frequency (Typical)

1kHz ± 1%

Display

Display Type

7 inchs TFT (diagonal liquid crystal)

Display Resolution

800 (horizontal) × 480 (vertical) pixels

Display Type

Point, vector

Waveform Brightness

Adjustable

Grid Type

Adjustable

Grid Brightness

Adjustable

Screen Brightness

Adjustable

Display Colour

16 million colours (24 bits true colour)

Persistence time

Minimum, 1s, 5s, 10s, 30s, infinite

Interface

Standard Interface

USB Host, USB Device

Power Supply

Supply Voltage

100 ~ 120VAC RMS  (±10%), 45Hz to 440Hz, CAT   II

120 ~   240VAC RMS  (±10%), 45Hz to 66Hz, CAT  I I

Power Consumption

<15W

Fuse

T2A 250VAC 4*8

Environmental

Operating Temperature

0 to 50 °C (32 to 122 °F)

Storage Temperature

− 40 to +71 °C ( − 40 to 159.8 °F)

Humidity

≤ +104°F (≤ +40°C): ≤90% relative humidity

Cooling Method

106°F ~ 122°F (+41°C ~50°C): ≤60% relative humidity

Altitude

Operating and Nonoperating

3,000m (10,000 feet)

Random Vibration

0.31g RMS  from 50Hz to 500Hz, 10 minutes on each axis

Nonoperating

2.46g RMS  from 5Hz to 500Hz, 10 minutes on each axis

Mechanical Shock

Operating

50g, 11ms, half sine

Mechanical

Dimension

 318 × 110 × 150mm (L × W × H)

Weight

1900g