1-1/16 microstep setting-Higher accuracy and smoother operation than standard 1, 1/2 step
Adjustable 1.5A-3A drive current settings for each axis - 25%,50%,75%,100% of full current can be set for different stepper motors.
*Attention: This driver is 1.5A-3A version, which is specially designed for stepper motors with rated current from 1.5A to 3A. It's NOT compatible with stepper motors with rated current below 1.5A or above 3A.
Overload, over-current and over-temperature safety-Full protection for your computer and peripheral equipment.
On board current switching-Power output can be set according to specific user requirement.
Full closed-type optical isolation to protect the user's computer and equipment.
Relay spindle interface-Outputs Max. 36V 7.5A for spindle motors or coolant pump (only one device can be powered by this output!)
4 channel inputs interface-Can be used for XYZ limit and emergency stop.
Professional design-Two stage signal processing with super anti-jamming.
Bipolar constant current chopper drive with non-resonant region - Controls motors smoothly through range without creep effect.
Four-input Control; Allow setting the Limit, Emergence-Stop, Midpoint-Alignment, Cutter-Alignment.
Universal architecture-Supports most parallel software MACH3,KCAM4 etc.
*For compatibility with other softwares, please feel free to contact us.
Current Setting | 1 | 2 | Decay Mode Settings | 3 | 4 | MicroStep Settings | 5 | 6 |
100% | ON | ON | FAST | ON | ON | 1 | ON | ON |
75% | ON | OFF | 25% | ON | OFF | 1/2 | ON | OFF |
50% | OFF | ON | 50% | OFF | ON | 1/8 | OFF | ON |
25% | OFF | OFF | SLOW | OFF | OFF | 1/16 | OFF | OFF |
12-16V DC power supply for Nema 17 stepper motors
16-24V DC power supply for Nema 23 stepper motors
(High voltage will burn up the chips or stepper motors!!!))
Ampertage Selection:Output current of the power supply can be calculated by the following expressions:
Output current = Rated current of your stepper motors * quantity + 2A
(For example, if you want to drive 3 * 3A Nema 23 stepper motors, theoretically 24V 11A DC power supply is recommended, but higher power such as 24V 15A also will be good. If you are not sure about the selection of power supply, please feel free to contact us for help).
Please SHUT DOWN the power before you plug or unplug the connectors to avoid burning up the board
These external tools on the left and bottom of the following picture are only for exhibition. We don't have them for sale at the moment.
Electrical properties (ambient temperature Tj = 25 °C pm): | ||
Input Power | 12-30V DC power supply | |
Stepper motor drive current | 1.5A - 3A/phase | |
Drive type | Double-pole constant flow PWM actuation output | |
Compatible Stepper motors | 2 or 4 phase, 4,6 or 8 lead stepper motors, 3A max. | |
Dimensions | 18 * 14 * 4 cm (L*W*H) |
1 x 3 Axis TB6560 Stepper Motor Driver 1.5A-3A
5 x Wire connectors
1 x White ribbon 5-pin limited cable
1 x DB25 parallel cable
1 x CD Driver
Estimated Delivery Time | ||
Australia (NSW) | Australia Post | 2-3 business days |
Australia (VIC,SA,QLD,NT) | Australia Post | 4-6 business days |
Australia (WA,TAS) | Australia Post | 6-8 business days |
New Zealand | Australia Post | 6-9 business days |
Other Countries (May depart from other stock location) | International Airmail Service | 12-21 business days |