Ancel BA101 12V Auto Car Battery Load Tester Cranking Analyzer Tool 100-2000CCA

ANCEL BA101 12V Car Battery Tester Analyzer 2000CCA 220AH Charger Battery System Test Car Charging Circut load Diagnostic Tools

ANCEL BA101 Battery Tester adopts currently the world's most advanced conductance testing technology to easily， quickly and accurately measure the actual cold cranking amps capability of the vehicle starting battery， healthy state of the battery itself， and common fault of the vehicle starting system and charging system， which can help maintenance personnel to find the problem quickly and accurately, thus to achieve quick vehicle repair.

Why choose BA101 products?

Small compact design, scan faster and indicates test results directly. Even a beginner can use this unit to analyze any 12V batteries healthy, tells you everything about the battery: voltage, charge, cranking power, and how much life is left in the battery (level of Ohm resistance). Does it quickly and precisely.

Much wider test range (100-2000 CCA) and more accurate compared to its competitors. Test results based on JIS, EN, DIN, SAE, CCA, BCI, GB, CA, MCA and IEC Standards.

Provides check the Alternator's charging and Starter's cranking conditions. Vehicle charging system test is also available, including load voltage, unloaded voltage, ripple status and charging system status.

The BA101 battery tester is well built with a large LCD display that has white backlight and contrast adjustment, indicates test results directly. no internal batteries required and gets the power directly from the 12V battery.

It's equipped with a 3. 0 feet long cable and made of a very thick flexible insulator, much safer than others selling on the marketplace. There are 4 buttons on BA101, The up/down button for scrolling the menu. The Enter and Exit button allow for navigation back and entering menu.

Ancel BA101 Car Battery Tester 12V Digital Battery Tester Analyzer

Ancel BA101 Car Battery Tester 12V Digital Battery Tester Analyzer

1. Accurate tester result in miliseconds (tolerance ±15)
2. BA101 can testCCA100-2000, 30-220Ah, which is the highest CCA in the market
3. Test batterues on and off the vehicle
4.Battery life analysis, Life in percentage (%),Internal resistance value (m),Capacity - Cold Cranking Amps (CCA), DIN, EN and IEC information relative to battery rating.
5. Test result based on JIS, EN, DIN, SAE and IEC standards.
6. Easily readLCD screen display
7.Quick test- input battery volume (AH), then it can show the battery status.
8. vehiclecranking system test- cranking time, voltage and status.
9.vehiclecharging system test- load voltage, unloaded voltage, ripple status and charging system status.
10. Store the testing result,print function
NOTICE:the device don't need ch

ANCEL BA101 Function:

Main functions of BA101 battery tester include： battery test，cranking test，charging test and other additional functions.

Battery Test

is mainly targeted to analyzethe battery healthy status to calculate the actual cold cranking capability of the battery and the
aging extent, which provide reliable analysis evidence for the test and maintenance of the battery. It notifies the user to replace battery in
advance when the battery getting aged.

Cranking Test

is mainly to test and analyze the starting motor. Through testing the actual required cranking current and cranking voltage of the starting motor，it can find out whether the starting motor works fine. There are several reasons why the starting motor is abnotmal: lubricating system fault causing the starting loaded torque increasing or rotor friction of the starting motor causing the in creasing friction of the starting motor itself.

Charging Test

is to check and analyze the charging system， including generator，rectifier，rectifier diode， etc.， thus to find out whether the output voltage of the generator is normal， the rectifier diode works fine and the charging current is normal. Suppose one of the above mentioned parts is not in normal situation， it will lead to over charge or incomplete charge of the battery， thus the battery will be quickly damaged and also greatly shorten the using life of other loaded electrical appliance.

ONE-CLICK QUICK TEST

It can test the 12V Vehiicle battery status,including

It can make sure the battery status, including voltage, CCA, electronic resistance, rated CCA, charging value, healthy value and testing result in one second. Once input the AH value—battery rated capacity, which is marked in the label of the battery.

1). Press UP/DOWN key to select the Quick test, then press ENTER key to confirm.

Wide Range of Application of ANCEL BA101 Battery Tester

ANCEL BA101 can test 12V batteries, suitable for a variety of common models and equipment.

ANCEL BA101 supports test all automotive cranking lead acid battery， including ordinary lead acid battery， AGM flat plate battery， AGM spiral battery，and Gel battery， EFB battery， etc.

Ancel BA101 Battery Test Result

GOOD BATTERY:the battery is without any problem , please be relaxed to use.
GOOD, RECHARGE:good battery , but low current,recharge before using it.
REPLACE:The battery is near to or already reached the end of using life, replace battery, otherwise, bigger danger will be followed.
BAD CELL, REPLACE:Battery interior damaged, bad cell or short circuit, and replace the battery.
CHARGE-RETEST:Unstable battery shall be recharged and retested to avoid error

Ancel BA101 Automotive 12V Vehicle Battery Testsing Steps

1. Quick test
It can make sure the battery status, including voltage, CCA, electronic resistance, rated CCA, charging value, healthy value and testing result in one second. Once input the AH value—battery rated capacity, which is marked in the label of the battery.
1). Press UP/DOWN key to select the Quick test, then press ENTER key to confirm.
2). Input the rated battery capacity—xx AH, in general, the battery capacity for 12V vehicle is above 30AH.
3). Then press enter key, the testing result will show one of these, as below Battery test result includes 5 types as following:
Good Battery: The battery is without any problem, please be relaxed to use
Good, Recharge: Good battery but low current, recharge before using.
Replace: The battery is near to or already reached the end of the using life, replace battery, otherwise, bigger danger will be followed.
Bad Cell, Replace:Battery interior damaged, bad cell or short circuit, replace battery.

3. Cranking Test and Charging Test

Ancel BA101 has Two Multi-Language Version

1.European Version: English, Spanish, French, German, Italian, Polish

2.Asian Version: English,Japanese, Korean, Chinese

Multiple Battery Standards Support

It can test by AH and CCA values but also applies to other test standards such as BCI, CA, MCA, JIS, DIN, IEC, EN, SAE, GB.

If your battery standard is AH standard, you can input the AH value to test in the "Quick Test" menu.

If your battery is CCA or another standard, please input the CCA or other value to test in the "Battery in Vehicle" or "Battery out of vehicle" test menu.

Fast and Accurate Reading

It adopts the world's most advanced conductance testing technology to date for accurate and authoritative test results.

It quickly analyzes the data, usually taking 2-3 seconds to display the results.

Easy to use, it can quickly and accurately identify battery problems.

Print Data Steps

Before using the print data function, it is necessary to connect the tool to a computer via the USB cable. Once ready, please insert the CD to the computer.

Install the USB driver first.

Open the print software, and choose the COM Port NO.

Then choose the function of print data to start printing.

How to Use Print data function ?

Step 1. Please kindly connect the tool to the computer once you want to print the test result;

Step 2. Install the USB driver firstly;

Step 3. Then open the Print software, and choose the COM NO;

Step 4. Then begin the print.

Note：

Ancel BA101 Test Data Print Out for WIN7
Please leave us email address to get the print out drive and software for laptop

Or download in Our Ancel official net : [link removed by eBay]

Ancel BA101 Car Battery Tester Application

Use to test a wide range of 12V batteries (Starting [SLI], Deep Cycled and Marine) of Wet (Flooded), VRLA or Maintenance Free (MF), Sealed Maintenance Free (SMF), Absorption Glass Mat (AGM) and GEL cell. The major battery standards JIS, SAE, EN, DIN and IEC are supported.

Technical Parameters:

1.Cold Cranking Amps Measure Range:

2. Voltage Measure Range: 8-30V DC

3.Working Environment Temp: -20°C-60°C

It is applicable for automotive manufacturers， automotive maintenance and repair workshops， automotive battery factories， automotive battery distributors， and educational organizations，etc

Package List:

1* Ancel BA101
1* User Manual
1* USB Cable（Provides link to unit and computer for printing.）