NEJE A40640 laser head module for cnc laser engraver cutter 12W & air assist AU
NEJE A40640 laser head / module for laser engraver / cutter FAC TECH 12W OUTPUT
A40640 (The most widely used module) is a classic creative master dual beam zoom laser module, it is the world's first 2 beam laser diode engraving and cutting module with zoom design, with the best metal engraving ability, fast groove engraving ability, thick material cutting compatibility, Make it the most widely used module. Due to the built-in NEJE unique fiber compression technology, It has a very strong energy density (0.04x0.06mm with 12W+ pulse and 11W continuous optical power), There are very special and top artistic expressions on the carvings of stainless steel grayscale carvings, stone carvings, Glass Carving, hardwood reliefs, canvas art, and other materials. The A40640 is the only high-power module with variable focus section, The optimized A40640 II has higher cutting reliability, The short focus is suitable for carving hard materials such as metal stone and cutting materials with high density such as mdf, The long focus has better depth of field and smaller included angle for cutting thick wood and other materials. The excellent design makes the A40640 have a very strong vitality from the first creator of high-power diode laser to today, Due to the high power density, it has an equivalent application higher than 20W (optical power) laser in large area image engraving, If you only consider 1 module to help you solve all the needs, it is the best choice.
The NEJE A40640 module adjusts the focus to Long focal end by default. This is because the NEJE factory has to ensure the consistency of product testing.
When you receive the product, it is recommended to use a flat-blade screwdriver to adjust the focus to 2-3mm from the light shield.
It is normal for the A40640 module to be slightly non-uniform in the XY direction of the far focus. This is a compromise of zoom design, not a quality problem. You can reduce the non-uniform XY cutting by narrowing the focus.
The lens can be rotated with a flat blade screwdriver. prevent the lens from leaving the module and prevent dust from entering the interior to damage the optical system.
The outside of the lens will be stained with the surface due to smoke or oil and water, and the lens will be burned due to the accumulation of beam energy. Therefore, try to keep the habit of cleaning at the beginning of each use or after the introduction.
When cutting MDF leather and other materials, it is necessary to reduce the cutting focus, and add air assistance of no less than 30psi. The NEJE A40640 module gives away metal high-pressure air assistance, which does not require additional purchase.
When the air compressor is used as the air source, an oil-water filter needs to be added. Ordinary oil-water separators cannot filter oil-water 100%, so they need to be cleaned regularly (several hours) If you plan to use it for cutting wood, leather and other materials for a long time, it is recommended to purchase high-quality high-capacity oil and water filters Note that the ordinary oxygen generator can only be used for protecting the left and right of the lens. It is recommended to start it during normal engraving or ordinary cutting.
When do you need high pressure air assist?
Air-assisted engraving or cutting can only be used for engraving or cutting that produces more carbonized substances. Generally, the depth of engraving is less than 1mm, and the cutting of plywood less than 2mm does not require air assist. A small fan can be used to blow off the smoke generated by the engraving. Air assist is not recommended when engraving images, and adding air assist at this time will destroy image details.
If your project will produce more smoke, it is recommended to use an oxygen generator to protect the lens for a long time.
If you are used to cut wood, MDF, cardboard, leather and other materials that produce a large amount of carbonized substances and need at least 30psi of air assistance, it is recommended to use the air valve accessories provided by NEJE to control high-pressure gas
A40640 Laser Module Feature
- Designed for Laser Engraver, 3D printer, CNC mill, Arduino project.
- 10W Optical power output, 4mm plywood from 1 pass(speed 200), 3mm black acrylic board from 1 pass, Able to engrave stainless steel, but it needs good focus adjustment.
- More Safety, Built-in protective glass to protect eyes! Even without wearing protective glasses, the operation is more comfortable.
- More Quiet, Intelligent drive adjust the cooling fan speed according to laser temperature.
- Easy use, Digital PWM wave pulse signal generator adjustable frequency duty cycle board for NEJE laser module.
- slidable mounting fixture is provided for easy adjustment of focus.
General Specification
Model:NEJE A40640 Module
Heatsink Material:Aircraft Aluminum + Brass Shell
Luminous Color:Blue
Section Size:40mm x 40mm
Cooling Mode:Temperature sensor intelligent control + 10000 rpm 40mm cooling fan
Dimension:60 * 40 * 40mm
Adapter Plug:5.5 2.1 port
Can Engrave:MDF/Balsa/Paper/Wood/Fabric/Plastic/Leather/Plywood/Foam Paper/Anodized Aluminum
Can Not Engrave:Metal/Glass/Stone/Ceramics/PCB/Stainless Steel/Reflective Material/ Transparent Material
Technical Parameters:
Optical power output:10W
Wavelength:445-450nm
Beam Shape:Dot (Focusable)
Working Voltage:DC 12V
TTL&PWM Modulation:YES, Compatible with Both TTL & PWM Modulation
Input Voltage:DC12V 3-4A
PWM/TTL Input:DC3.3V-12V
Input Interface:PH2.0-4Pin (+,-, PWM/TTL, Temperature), 3Pin (+,-, PWM/TTL) , 2Pin+2Pin (+,-) + (PWM/TTL,-)
NOTE:Temperature interface can be disconnected,NEJE provides text instructions for temperature acquisition on the wiki.
Drive Mode:External ACC
Safe temperature range:<60 ℃
Module weight:202g ( The lighter the weight, the smaller the moving inertia, the better the performance )
Life Time:10000-20,000 hours
Digital PWM Wave Pulse Signal Generator Adjustable Frequency Duty Cycle for NEJE Laser Module tester board Specification
Power input: DC 12V
Output: PH2.0 4pin (12v,GND,PWM/TTL,Temperature)
mode: 3 modes (off, manual pwm, pwm / ttl in)
temperature display: YES
pwm display: yes
Manual PWM control: YES
Note(Please pay attention)
A40640 Laser Module Kits Package Included
A40640 module x1,
KF40 Air-Assisted Mounting Kit x1,
Trachea 2m x1,
Trachea adapter x1,
Interface adapter board x1,
Wire pack x1,
Module general manual x1,
Sliding card slot (stick the stable silicone pad and install the screw x1,
Large and small Allen key installation kit x1,
PWM test board with screen x1;
1. We will provide the best service and reliable products for every customer, however, accident may happen sometimes,We believe good cummunication can solve every problem happily, so pls contact us to solve any issue before leaving a negative feedback.
2. We will reply you ASAP. If you don't get response within 1-2 business days, pls check your eBay email or My Messages in case your email provider has an overly-aggressive spam filter blocking eBay or my e-mails. Please add us in your contact and email us again.
Working days: Monday - Friday
Payment must be made within 5 days after your bidding. (Non-payment may result in a UPI (Unpaid Item) being put on your account.)
Shipping Method Tracking Number Delivery Time
Standard shipping from China YES 7-19 Business Days
Attention: No shipping on Saturday Sunday or Public Holidays & No responsibility for any customs duty.
(1).If there's any problem, please do not hesitate to contact us by eBay message, we will reply you within 1 business day. (not include Public holiday)
(2).All returns - defective or otherwise - have to be preauthorized. Please contact us to get an authorization and returning address before sending the item back.If an item is returned because of an undeliverable shipping address, buyer agrees to pay the cost for re-shipment.
(3).Please note that If the return/replacement is not a result of our mistake (not defective or wrong item), the buyer is responsible for return shipping fee.
As we are honest seller,we live on feedback ,so your positive feedback and 5-star DSRs means a lot to us.
We would very much appreciate it if you would leave us a 5-star positive feedback
About Us
1. We will provide the best service and reliable products for every customer, however, accident may happen sometimes,We believe good cummunication can solve every problem happily, so pls contact us to solve any issue before leaving a negative feedback.
2. We will reply you ASAP. If you don't get response within 1-2 business days, pls check your eBay email or My Messages in case your email provider has an overly-aggressive spam filter blocking eBay or my e-mails. Please add us in your contact and email us again.
Working days: Monday - Friday
PaymentPayment must be made within 5 days after your bidding. (Non-payment may result in a UPI (Unpaid Item) being put on your account.)
ShippingShipping Method Tracking Number Delivery Time
Standard shipping from China YES 7-19 Business Days
Attention: No shipping on Saturday Sunday or Public Holidays & No responsibility for any customs duty.
Returns
(1).If there's any problem, please do not hesitate to contact us by eBay message, we will reply you within 1 business day. (not include Public holiday)
(2).All returns - defective or otherwise - have to be preauthorized. Please contact us to get an authorization and returning address before sending the item back.If an item is returned because of an undeliverable shipping address, buyer agrees to pay the cost for re-shipment.
(3).Please note that If the return/replacement is not a result of our mistake (not defective or wrong item), the buyer is responsible for return shipping fee.
Contact UsAs we are honest seller,we live on feedback ,so your positive feedback and 5-star DSRs means a lot to us.
We would very much appreciate it if you would leave us a 5-star positive feedback
NEJE 3 Max A40640 Laser Engraving Cutting Machine WOOD Engraver CUTTER 12W AU-1
559.0 AUD
Free shipping
54X 85 CM Honeycomb Platform Bed Working Table for max Laser Engraving Cutter au
229.0 AUD
Free shipping
NEJE 3 E40 LASER ENGRAVER &CUTTER 11W laser engraving machine 170 X 170 mm
459.0 AUD
Free shipping
NEJE N30820 laser module head For CNC laser engraving cutting machine 5.5W AU-01
159.0 AUD
6.0 AUD
NEW NEJE Max 4 E80 laser engraver & cutter 20w laser engraving machine w/Z-axis
1399.0 AUD
Free shipping
NEJE 3 Max E40 Laser Engraving Machine 10W Laser Module Engraver laser cutter
559.0 AUD
Free shipping